說明書 SAMSUNG SYNCMASTER 213T

[. . . ] SyncMaster 213T ӌ਄ ֜դऐՂ ത჆ !ᄽိ ֜ი ೎፥ ‫ܡ‬Ӕ ҧۢ ིᎣ ࢛৿ߨ ࣵ৿ߨ ֜ი එ౷‫࠱؃‬ᣩՂᑴ ֜იᣩՂᑴᢀ௯໓٧ ‫מ‬௯࠱ ҫ௯ !! ᣩՂևᔛᆟт चኽಈை ᗀषࡤ ంᜲቖற໠ ‫ٺמ‬ຓტӤ୨૽ᚚᗀष ‫ޤ‬୨ऐፑ ᘔᣯ࠱‫ޤ‬୨ऐፑ ႏᄽᑴ ᅃቹ઴ུፓ֤ ஛઒ ߚ௭ ൬ቿ ൵࢞࠱ Obuvbm!Dpmps ‫܌‬ᣩՂ‫ړ‬೎๐!ᢞ৻ ത჆ ᄽိ ֜ი ೎፥ ‫ܡ‬Ӕ ! [. . . ] You may find the booklet called How to Identify and Resolve Radio/TV Interference Problems helpful. This booklet was prepared by the Federal Communications Commission. Government Printing Office, Washington, DC 20402, Stock Number 004-000-003454. Warning User must use shielded signal interface cables to maintain FCC compliance for the product. Declaration of conformity for products Marked with FCC Logo This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. The party responsible for product compliance: SAMSUNG ELECTRONICS CO. , LTD America QA Lab of Samsung 85 West Tasman Drive San Jose, CA 95134 USA Tel) 408-544-5124 Fax) 408-544-5191 Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It may be suitable for connection to any UL Listed personal computer with similar configuration. Before making the connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage rating. For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 5-15P type (parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable power supply cord with NEMA configuration 6-15P type (tandem blades) plug cap. IC Compliance Notice This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations of ICES-003. MPR II Compliance This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields. European Notice(Europe Only) Products with the CE marking comply with the EMC Directive(89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms: !! EN55022:1998+A1:2000 - Radio Frequency Interference EN55024:1998 - Electromagnetic Immunity of Information Technology Equipment EN61000-3-2:1995+A1/A2:1998 - Power Line Harmonics EN61000-3-3:1995 - Voltage Fluctuations PCT Notice CCC Notice TCO'95-Ecological requirements for personal computers (TCO'95 applied model only) AB general requirements AB2 Written Eco-document acompanying the products Congratulations!You have just purchased a TCO'95 approved and labelled product!Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products. Why do we have environmentally-labelled monitors?In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment. The main problem as far as monitors and other electronic equipment are concerned is that environmentally harmful substances are used both in the products and during their manufacture. Since it has not been possible so far for the majority of electronic equipment to be recycled in a satisfactory way, most of these potentially damaging substances sooner or later enter Nature. There are also other characteristics of a monitor, such as energy consumption levels, that are important from both the working and natural environment viewpoints. Since all types of conventional electricity generation have a negative effect on the environment (acidic and climate-influencing emissions, radioactive waste, etc. ) it is vital to conserve energy. Electronic equipment in offices consumes an enormous amount of energy, since it is often routinely left running continuously. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to other devices, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: !! ! Reorient or relocate the receiving device. Increase the separation between the equipment. [. . . ]