說明書 PHILIPS RQ1075 TECHNICAL SPECIFICATIONS
Lastmanuals提供軟硬體的使用指南,手冊,快速上手指南,技術資訊的分享,儲存,與搜尋 別忘了:總是先閱讀過這份使用指南後,再去買它!!!
如果這份文件符合您所要尋找的使用指南, 說明書或使用手冊,特色說明,與圖解,請下載它. Lastmanuals讓您快速和容易的使用這份PHILIPS RQ1075產品使用手冊 我們希望PHILIPS RQ1075的使用手冊能對您有幫助
Lastmanuals幫助您下載此使用指南PHILIPS RQ1075
您也可以下載以下與您要搜尋的產品相關的手冊
PHILIPS RQ1075 (5922 ko) PHILIPS RQ1075 TECHNICAL SPECIFICATIONS (1118 ko)
手冊摘要: 使用說明書 PHILIPS RQ1075TECHNICAL SPECIFICATIONS
在使用指南中有清楚的使用說明
[. . . ] • Slowly close the housing by pushing it down until it locks. The cleaning fluid display 1 will show how much fluid is in the cartridge:
1
2
fast clean
new
st
a rt
cleaning
clean
eco
norm
n
al
fast clea
high low empty
intens
auto
ive
st
a rt
cleaning
clean
eco
l norma
n
t selec
fast clea
high low empty
intens
auto
ive
t selec
fast clean
fast clean
high
high low empty
high low empty
«high» up to 30 cleaning cycles available «low» up to 7 cleaning cycles remaining «empty» new cartridge required
low empty
If required, the Clean&Renew station will now charge the shaver. The hygiene status of the shaver will also be analyzed and one of the following cleaning program diodes 5 will light up: «clean» «eco» «normal» «intensive» shaver is clean short economical cleaning required normal level of cleaning required high intensive cleaning required
high
low empty
s ta
f a st c le a n
high
low
ble washa
If the station selects one of the required cleaning programs, it will not start unless you press the «start cleaning» button 4. For best shaving results, we recommend cleaning after each shave.
wash
able
reset
Charging and cleaning the shaver Insert the shaver head down into the cleaning station. [. . . ] Each cleaning program consists of several cycles, where cleaning fluid is flushed through the shaver head and a heat drying process dries the shaver. Depending on the program selected the total cleaning time will range from 32 to 43 minutes. The cleaning programs should not be interrupted. Please note that whilst the shaver is drying, the shaving head may be hot and wet. When the program is finished, the blue «clean» diode will light up. Your shaver is now clean and ready for use. Fast cleaning Push the «fast clean» button D to activate the fast clean program without drying. This program takes about 25 seconds only and is recommended when you do not have time to wait for one of the automatic cleaning programs. If you remove the shaver just after the program has finished, wipe off the shaver head with a tissue to avoid dripping. Stand-by mode 10 minutes after completing the charging or cleaning session, the Clean&Renew station switches to the stand-by mode: The diodes of the Clean&Renew station turns off.
s ta
rt cleaning
clean eco normal
f a st c le a n
intensive auto select
high
low empty
14
ble washa
st
a rt
cleaning
clean
eco
normal
f a st cle
an
intensive
ct auto sele
Shaver display
The shaver display r shows the charge status of the battery on the left, and the hygiene status on the right. (6 dark segments are shown on each side when the battery is fully charged and the shaver is hygienically clean). Each cartridge, if not used daily, should be replaced after approximately 8 weeks. The cleaning cartridge also contains lubricates, which may leave residual marks on the outer foil frame after cleaning. However, these marks can be removed easily by wiping gently with a cloth or soft tissue paper. Manual cleaning The shaver head is suitable for cleaning under running tap water. Warning: Detach the shaver from the power supply before cleaning the shaver head in water. Rinsing the shaving head under running water is an alternative way to keep the shaver clean, especially when travelling: • Switch the shaver on (cordless) w and rinse the shaving head under hot running water. You may use liquid soap without abrasive substances. Rinse off all foam and let the shaver run for a few more seconds.
washable
high
low empty
release
on
er
release
washable
click!
trimmer
release
16
e washabl
wa
sh
reset
er trimm
s ta
rt cleaning
clean
eco
norma l
fast clea
n
ive intens
auto select
ab
le
trim me r
• Next, switch off the shaver, press the release button 9 to remove the foil and cutter cassette 8 and let it dry.
oil
• If you regularly clean the shaver under water, then once a week apply a drop of light machine oil on top of the foil and cutter cassette.
Alternatively, you may clean the shaver using the brush provided: • Switch off the shaver. Remove the foil and cutter cassette 8 and tap it out on a flat surface. Using the brush, clean the inner area of the pivoting head. However, do not clean the cassette with the brush as this may damage it. [. . . ] Cleaning the housing From time to time clean the housing of the shaver and the Clean&Renew station with a damp cloth, especially inside the cleaning chamber where the shaver rests. Replacing the cleaning cartridge After having pressed the lift button 2 to open the housing, wait for a few seconds before removing the used cartridge to avoid any dripping. Before discarding the used cartridge, make sure to close the openings using the lid of the new cartridge, since the used cartridge will contain contaminated cleaning solution.
release
release
washable
release
washable
washable
new
old
Keeping your shaver in top shape
Replacing the foil and cutter cassette / reset To maintain 100% shaving performance, replace the foil and cutter cassette 8, when the replacement symbol lights up on the shaver display r (after about 18 months) or when cassette is worn. The replacement symbol will remind you during the next 7 shaves to replace the foil and cutter cassette. [. . . ]
放棄下載這份使用手冊 PHILIPS RQ1075
Lastmanuals提供軟硬體的使用指南,手冊,快速上手指南,技術資訊的分享,儲存,與搜尋
在任何的情況下, Lastmanuals都沒有任何的責任: 如果您所搜尋的文件結果是不存在的,不完整的,不是您的母語的, 或是型號或語言與描述不符. Lastmanuals不提供翻譯的服務
如果您接受這份合約內容, 請在閱讀完此約後,按下“下載這份使用手冊”, 下載PHILIPS RQ1075手冊的過程馬上開始.