說明書 KLIPSCH RC-7

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. You can determine whether your computer system is causing interference by turning it off. If the interference stops, it was probably caused by the computer or one of the peripheral devices. If your computer system does cause interference to radio or television reception, try to correct the interference by using one or more of the following measures: • Turn the television or radio antenna until the interference stops. [. . . ] If you have an internal Apple CD-ROM, DVD-ROM, or DVD-RAM drive in your computer, your computer is a Class 1 laser product. The Class 1 label, located in a user-accessible area, indicates that the drive meets minimum safety requirements. A service warning label is located in a service-accessible area. The labels on your product may differ slightly from the ones shown here. Exposure to Radio Frequency Energy The radiated output power of the optional AirPort Extreme Card is far below the FCC radio frequency exposure limits. Nevertheless, it is advised to use the wireless equipment in such a manner that the potential for human contact during normal operation is minimized. Mouse and Keyboard Information The Apple optical mouse is a Class 1 LED product. This product complies with the requirements of European Directives 72/23/EEC and 89/336/EEC. It also complies with the Canadian ICES-003 Class B Specification. ̯ཋ຾உௐɺ˿͂‫כ‬ኧА࣏ɥஉ‫ܪ‬dॾ‫ي‬ኒॾֶ ஝঩ӡ଻dॾ‫ဳي‬Թӡ଻ֶͨЄԯˢ˿ॶΐ‫ݯ‬ཋ ຾‫ܨ‬჋ϤኒߎɁࡗϋədඬࡻֶᗲࠇ᏷ྊӎࡻɾ ͂பe ঢ়΀፮‫৽ݠ‬ᘬй ENERGY STAR® Compliance Class 1 label Service warning label Laser Specifications for Combo Drive Laser on pickup unit when reading a DVD: • Type: Semiconductor laser GaAs/In(GaAI)P/InGaP • Wavelength: 655 ± 15 nm • Power out of objective lens: 0. 33 mW • Beam divergence: 20º ~ 35º (Typical 27º) Laser on pickup unit when reading a CD: • Type: Semiconductor laser AIGaAs/GaAs • Wavelength: 784 ± 8 nm • Power out of objective lens: Read = 1. 0 mW, Write = 80. 0 mW • Beam divergence: 14. 5º ~ 17. 5º (Typical 16º) Laser Specifications for CD Laser on pickup unit when reading a CD: • Type: Semiconductor laser AIGaAs • Wavelength: 78 ~ 800 nm (Typical 790 nm) • Power out of objective lens: Read = . 11 mW, • Beam divergence: 14º ~ 20º (Typical 17º) As an ENERGY STAR® partner, Apple has determined that standard configurations of this product meet the ENERGY STAR® guidelines for energy efficiency. The ENERGY STAR® program is a partnership with office product equipment manufacturers to promote energy-efficiency. Reducing energy consumption of office products saves money and reduces pollution by eliminating wasted energy. ᇼԗ๑੬ֺΕΔਂ‫ؿ‬᏷‫ړ‬ஃ௃՗‫͐ܞ‬Ԟ୮ଉᄠૃ ‫ؿ‬ཋϑe Nederlands: Gebruikte batterijen kunnen worden ingeleverd bij de chemokar of in een speciale batterijcontainer voor klein chemisch afval (kca) worden gedeponeerd. ཋϑ୮ଉ༅঩ ཋ໷՗ Apple 56K ᅕኣዀ༅঩ ஝‫ك‬੬‫ؿ‬ཋ໷ʔ̇ ๫੬Εཋ໷ᇃ༏ɐܼஉᅕኣዀஉௐɾ‫ک‬cܺԒ ཋ໷ʔ̇˿ॶผ߬ұ੬ԑͱ஝‫ك‬ԯ๫Δ‫ؿ‬Ꮺพ ௰Ͻe 98 Information You Need in the United States The internal modem complies with Part 68 of the FCC rules. On the back of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN). If requested, provide this information to your telephone company. In some cases, you may extend the company’s internal wiring for single-line individual service by means of a certified telephone extension cord. Be aware, however, that compliance with these conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any equipment malfunctions or repairs or alterations that you make to this equipment may cause the telecommunications company to request that you disconnect the equipment. In Canada, contact Apple at: 7495 Birchmount Road, Markham, Ontario, L3R 5G2, 800-263-3394 Warning: Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. 99 Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority or electrician. • Load number: 0. 1 The load number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to the telephone loop that is used by the device, to prevent overloading. The termination of a loop may consist of any combination of devices, subject only to the requirement that the sum of the load numbers of all devices does not exceed 100. • Telephone jack type: CA-11 Informations Destinées aux Utilisateurs Canadiens L’étiquette d’Industrie Canada identifie un matériel homologué. Cette étiquette certifie que le matériel est conforme à certaines normes de protection, d’exploitation et de sécurité des réseaux de télécommunications. Le Ministère n’assure toutefois pas que le matériel fonctionnera à la satisfaction de l’utilisateur. [. . . ] To provide compliance with the Australian Communications Authority’s technical standards, please ensure that the following AT commands are maintained: • ATB0 (ITU/CCITT operation) • AT&G0 (no guard tone) • AT&P1 (33/66 pulse dial make/break ratio) • ATS0 = 0 or ATS0 = 1 (no answer or answer greater than one ring) • ATS6 = 95 (DTMF period between 70–255 ms) • ATS11 = 95 (DTMF period between 70–255 ms) For calls that are automatically generated, a total of three call attempts are allowed to a telephone number, with a minimum period between calls of 2 seconds. If the call does not connect after three attempts, 30 minutes must expire before automatic redialing may be initiated. Failure to set the modem (and any associated communications software) to the above settings may result in the modem being non-compliant with Australian telecommunications standards. Under these circumstances a user could be subject to significant penalties under the Telecommunications Act 1997. [. . . ]