說明書 KLIPSCH IMAGE S2

[. . . ] These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation. You can determine whether your computer system is causing interference by turning it off. If the interference stops, it was probably caused by the computer or one of the peripheral devices. [. . . ] For your safety, have this equipment serviced only by an Apple-authorized service provider. Because of the optical disc drive in your computer, your computer is a Class 1 laser product. The Class 1 label, located in a user-accessible area, indicates that the drive meets minimum safety requirements. A service warning label is located in a serviceaccessible area. The labels on your product may differ slightly from the ones shown here. Display Disposal Information The backlight lamp in this product contains mercury. Dispose according to local, state, and federal laws. ཋϑ୮ଉ༅঩ ᇼԗ๑੬ֺΕΔਂ‫ؿ‬᏷‫ړ‬ஃ௃՗‫͐ܞ‬Ԟ୮ଉᄠૃ ‫ؿ‬ཋϑe Nederlands: Gebruikte batterijen kunnen worden ingeleverd bij de chemokar of in een speciale batterijcontainer voor klein chemisch afval (kca) worden gedeponeerd. ̎ᜪi ཋ໷՗ Apple 56K ᅕኣዀ‫ޚ‬ᗐ༅঩ ஝‫ك‬੬‫ؿ‬ཋ໷ʔ̇ ๫੬Εཋ໷ᇃ༏ɐܼஉᅕኣዀஉௐɾ‫ک‬cܺԒ ཋ໷ʔ̇˿ॶผ߬ұ੬ԑͱ஝‫ك‬ԯ๫Δ‫ؿ‬Ꮺพ ௰Ͻe Information You Need in the United States The internal modem complies with Part 6B of the FCC rules. On the back of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN). If requested, provide this information to your telephone company. Â Ringer equivalence number (REN): 0. 1B The REN is useful to determine the quantity of devices you may connect to your telephone lines and still have all those devices ring when your telephone number is called. In most, but not all areas, the sum of the RENs of all devices connected to one line should not exceed five (5. 0). To be certain of the number of devices you may connect to your line, as determined by the REN, you should contact your local telephone company to determine the maximum REN for your calling area. Be sure you use an acceptable method of connection to install the equipment. In some cases, you may extend the company’s internal wiring for single-line individual service by means of a certified telephone extension cord. Be aware, however, that compliance with these conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any equipment malfunctions or repairs or alterations that you make to this equipment may cause the telecommunications company to request that you disconnect the equipment. In Canada, contact Apple at: 7495 Birchmount Road, Markham, Ontario, L3R 5G2, 800-263-3394 Warning: Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas. Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority or electrician. Â Load number: 0. 1 The load number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to the telephone loop that is used by the device, to prevent overloading. The termination of a loop may consist of any combination of devices, subject only to the requirement that the sum of the load numbers of all devices does not exceed 100. Â Telephone jack type: CA-11 Informations Destinées aux Utilisateurs Canadiens L’étiquette d’Industrie Canada identifie un matériel homologué. Cette étiquette certifie que le matériel est conforme à certaines normes de protection, d’exploitation et de sécurité des réseaux de télécommunications. [. . . ] To provide compliance with the Australian Communications Authority’s technical standards, please ensure that the following AT commands are maintained: Â ATB0 (ITU/CCITT operation) Â AT&G0 (no guard tone) Â AT&P1 (33/66 pulse dial make/break ratio) Â ATS0 = 0 or ATS0 = 1 (no answer or answer greater than one ring) Â ATS6 = 95 (DTMF period between 70–255 ms) Â ATS11 = 95 (DTMF period between 70–255 ms) For calls that are automatically generated, a total of three call attempts are allowed to a telephone number, with a minimum period between calls of 2 seconds. If the call does not connect after three attempts, 30 minutes must expire before automatic redialing may be initiated. Failure to set the modem (and any associated communications software) to the above settings may result in the modem being non-compliant with Australian telecommunications standards. Under these circumstances a user could be subject to significant penalties under the Telecommunications Act 1997. 102 This modem must be properly secured in order for you to use it. [. . . ]