說明書 EPSON STYLUS CX9300F

[. . . ] WARNING: Potential Shock Hazard 1 Read and understand all instructions in the Setup Poster. 2 Use only a grounded electrical outlet when connecting the unit to a power source. If you do not know whether the outlet is grounded, check with a qualified electrician. 3 Telephone lines can develop hazardous voltages. [. . . ] To install the tray ` Slide the legal-size tray onto the front paper-tray extender located on the ADF lid. Slide tray onto extender. 24 Chapter 5—Load paper or transparency film, or load originals AvPrn. book Page 25 Monday, February 28, 2000 11:13 AM EPSON OfficeJet G Series To use the ADF 1 Lift the lid, and make sure that the glass is clean. For more information, see “Clean the glass” in the Onscreen Guide. Place all originals in the legal-size tray with the printed side facing toward the back and with the top of the document pointing down. Align the paper with the left side of the legal-size tray. Insert legal-size or mix of legal- and letter-size originals vertically. When working with originals that were originally loaded in the ADF in vertical orientation, you may notice during processing that part of the original temporarily sticks out from under the lid and a short delay occurs. This is normal behavior. Avoid paper jams To avoid paper jams, remove papers from the output tray frequently. Output tray capacity is affected by the type of paper and the amount of ink you are using. For more information about output-tray capacity, see “Technical information. ” For help with clearing a paper jam, see the Troubleshooting Help available through the Director. Chapter 5—Load paper or transparency film, or load originals 25 AvPrn. book Page 26 Monday, February 28, 2000 11:13 AM EPSON OfficeJet G Series 26 Chapter 5—Load paper or transparency film, or load originals AvPrn. book Page 27 Monday, February 28, 2000 11:13 AM 6 Use the print features Most print settings are automatically handled by the program you are printing from or by EPSON’s ColorSmart technology. You only need to change the settings manually when you change print quality, print on specific types of paper or film, or use special features, such as two-sided printing. For comprehensive information, see the fully searchable Onscreen Guide. To access the guide, go to the Director, click Help, and choose Onscreen Guide. Start a print job Follow these steps to start a print job from the software program that you used to create your document. 1 2 Load the input tray with the appropriate paper. To scan your original and preview each page, select the Preview each page check box, and then click OK. • If you used the ADF and chose to scan all pages, your EPSON OfficeJet scans the original and sends the output to the selected destination. If you used the ADF and chose to scan a single page, your EPSON OfficeJet scans the document, and then the scanned image appears in the Scan window. In the Scan window, click Scan Next Page if you want to continue scanning additional pages one at a time. You can also click Scanning tips for more information on processing your scan. If you used the glass, your EPSON OfficeJet scans the document, and then the scanned image appears in the Scan window for you to edit, save, or send to a program. In the Scan window, click Scanning tips for more information on processing your scan. Chapter 7—Use the scan features 31 AvPrn. book Page 32 Monday, February 28, 2000 11:13 AM EPSON OfficeJet G Series Use an EPSON OfficeJet that is networked You can initiate a scan from your EPSON OfficeJet or PC. To do this from your EPSON OfficeJet 1 Load your original. For more information, see “Load originals on the glass” or “Load originals in the automatic document feeder (ADF). ” 2 Press Scan To repeatedly until your PC’s name appears on the front-panel display, and then press START SCAN. PC name Scan To Your EPSON OfficeJet scans the document, and then displays it in the EPSON Image Editor on the selected PC. For more information on using a specific name for your PC, see “Change the PC’s friendly name when using a networked EPSON OfficeJet. ” To do this from your PC 1 In the Director, click Scan. Click here to scan. 32 Chapter 7—Use the scan features AvPrn. book Page 33 Monday, February 28, 2000 11:13 AM EPSON OfficeJet G Series 2 After the Network Scan Setup dialog box appears, choose one of the following: • To scan your original and send it directly to a specific destination, go to the Send To list, and select the appropriate destination. In the Image Type area, select the image type, and then click OK. To scan your original and preview each page, select the Preview each page check box, and then click OK. • The Scan Reservation dialog box appears, and the EPSON OfficeJet is temporarily reserved for your scan. [. . . ] The EPSON OfficeJet G Series products can be used was a single device and/or in combination (in serial connection) with other approved terminal equipment. Geräuschemission LpA < 70 dB am Arbeitsplatz im Normalbetrieb nach DIN 45635 T. 19 For non-European customers This product is approved for use only in the country in which it was purchased. Local country laws may prohibit the use of this product outside the country of purchase. It is strictly forbidden by law in virtually every country to connect nonapproved telecommunications equipment (fax machines) to public telephone networks. VCCI-2 (Japan) Notice to users of the Korean telephone network Notice to users of the New Zealand telephone network 1 This equipment shall not be set to make automatic calls to the Telecom ‘111’ Emergency Service. [. . . ]