說明書 EPSON EPL-5700 安装手册

[. . . ] 5 ӵᚖ७ ӵᚖ७Ӗӟ൐ Ӗӟ൐ϯ೎ֶ ϯ೎ֶા . 8 ิᓃᅌ ิᓃᅌᎈ೎ֶ ᎈ೎ֶા . . 14 ఼ዓӟ ఼ዓӟߒᐠѴ ߒᐠѴ෦ . 14 ఼ዓ஝ ఼ዓ஝࡙ཐᔖ ࡙ཐᔖᏢ . [. . . ] ӵࠉ७‫ݖ‬ΰȂ‫ٺ‬Ңήጐဴ‫ܖ‬ΰጐဴࡸᗤ௢ଢ଼‫ڗ‬џӖӟ џӖӟॲ७ђ ॲ७ђ૖ߒȂณࡣࡸ OK ( ጂۡ ) ᗤȄ ‫ٺ‬Ңήጐဴ‫ܖ‬ΰጐဴࡸᗤ௢ଢ଼Ս‫ܚ‬ሯ‫ޟ‬џӖӟॲ७ ( ԃӖӟຨᘞॲ७ )Ȃณࡣࡸ OK ( ጂۡ ) ᗤȄ ђ૖ߒ໶Ҭ षሯџӖӟॲኵ‫ׇޟ‬ᐌ఼൐Ȃ፜Ӗӟ ȶђ૖ߒ໶Ҭȷ Ȉ 1. ᒵᐅࠉ७‫ݖ‬ΰ‫ޟ‬ђ૖ߒȂณࡣࡸ OK ( ጂۡ ) ᗤȄ ᒵᐅӖӟђ૖ ӟђ૖ߒ໶Ҭ ߒ໶ҬȂณࡣࡸ OK ( ጂۡ ) ᗤȄ ‫ܚ᠌ގ‬Ԥ © 2002 Xerox CorporationȄ߳੼Ιϸ᠌ցȄ 2 EPL-5700 COLOR PRINTER ® Diagnose Print Quality Problem Solution 1. From the printer's front panel Support Menu select Improve Print Quality?, then select Print Paper Tips Page and press OK. From the printer's front panel Support Menu select Improve Print Quality?, then select Print Paper Tips Page. Ensure the paper you are using is the correct type for the printer and is properly loaded. Ensure the paper loaded in the tray matches the paper type selected on the printer's front panel and in the printer driver. If the problem persists, select the appropriate Tray Setup Menu for the tray you are using and set the paper type to the next heaviest type of paper. Refer to the Paper Tips Page for media types and weight. Note: To access the Paper Type Menu, open and close the selected paper tray or re-insert the paper loaded in the MPT. The front panel will then prompt you to select the paper type. Incomplete Fusing Toner appears to be pulled off print, or is easy to rub off. Image Offset Toner appears to have been pulled off the page and placed about 82. 25 mm down the page from where it should be. 1. From the printer's front panel Support Menu select Improve Print Quality?, then select Print Paper Tips Page and press OK. The Cyan lines above that number should form a straight line with the black lines. Enter that number by using the Up Arrow or Down Arrow keys and press OK. Repeat steps a through c for Adjust Magenta and Adjust Yellow. Note: The adjustment value entered is stored and is now the new 0 positon for that color. Repeat the process until all three colors are aligned at the 0 position. Reprint this page to verify the adjustment. +7 +6 +5 +4 +3 +2 +1 0 -1 -2 -3 -4 -5 -6 -7 +7 +6 +5 +4 +3 +2 +1 0 -1 -2 -3 -4 -5 -6 -7 +7 +6 +5 +4 +3 +2 +1 0 -1 -2 -3 -4 -5 -6 -7 Page 1 of 1 EPL-5700 COLOR PRINTER ® Color Calibration Tutorial Overview Color calibration procedures adjust the printer for optimal color output. Color settings may need adjustment upon initial printer set-up or when toners and imaging units are replaced. There are two procedures: Lighten/Darken Colors and Balance Colors. If the overall image appears either too light or dark, use the Lighten/Darken Colors procedure. If a finer adjustment of the primary colors (cyan, magenta and yellow) are needed, continue with the Balance Colors procedure. Lighten/Darken Colors The Lighten/Darken Colors procedure uniformly increases or decreases each primary color (cyan, magenta, yellow and black) to produce a lighter or darker image. Select Lighten/Darken Colors from the Calibrate Colors Menu and press OK. [. . . ] The imaging area is shown as a dashed rectangle; the printer will not print outside this rectangle. To move the dashed rectangle to the postion you want it on the page: 1. From the printer's front panel Support Menu, scroll to Improve Print Quality?Scroll to the Calibrate Margins Menu and press OK. [. . . ]